Tasoth's next WIP
Moderator: Beowulf
Tasoth's next WIP
After a couple hours of work.
A couple more hours of work.
Just spent about 3 hours work on the pilot's console and right flight stick, majority being spent on the pain in the ass flight stick. More to come.
I've committed the greatest sin, worse than anything done here today. I sold half my soul to the devil. -Ivan Isaac, the Half Souled Knight
Mecha Maniac
Mecha Maniac
Requested shaded wireframe. Still needs a lot of work, mainly in the cockpit and from the nose back. Engines and weapons I've kinda figured out for placement. What sucks is Sketchup does not support parenting, which would make this much easier on me.
See how the front of the stick is round along the cutouts? Yeah, Sketchup doesn't like extruding along certain sized curves and results in massive tears and open patches. I had to go in and figure it all out by hand. Bleh.
EDIT: The demand for a shaded wireframe started me working on the model again.
Completed pilot station. Note the little pedals at the bottom. Had fun do that bit.
Close up of the pilot console. Big ol' sensor screen in the middle, various meters to the left and a panel of toggles, covered, to the right.
I did have a close up of the throttle, but it got eaten somwhere along the line.
I've committed the greatest sin, worse than anything done here today. I sold half my soul to the devil. -Ivan Isaac, the Half Souled Knight
Mecha Maniac
Mecha Maniac
- Ford Prefect
- Emperor's Hand
- Posts: 8254
- Joined: 2005-05-16 04:08am
- Location: The real number domain
Ah, yeah, that´s what modelling is about. Reparing stuff by hand. Or at least that´s the feeling i get sometimes.See how the front of the stick is round along the cutouts? Yeah, Sketchup doesn't like extruding along certain sized curves and results in massive tears and open patches. I had to go in and figure it all out by hand. Bleh.
Anyway, keep up the good work.
- Kenny_10_Bellys
- Jedi Knight
- Posts: 836
- Joined: 2003-01-20 07:19am
- Location: Central Scotland
- Contact:
For Sketch-up I'd say that was damn fine work. I didn't think Sketchup had it in it, but you've proved me wrong. Well done, cant wait to see the finished item.
visit http://www.kennyscrap.com for all your crap model needs.
RAR! Back!
Finished cockpit from outside the canopy.
Gunner's station with random buttons, emergency throttle, joystick and comm setup. Hud is the big uprights with additional screens below.
Close up of the flight stick. Firing stud, two additional buttons and a toggle plus comms console.
For instances when pilot is rendered incapacitated, grip safety and push throttle. Disengages the flightstick from the guns and into the drives. Figured something like that is best placed where the gunner can't bump it.
With those parts done, going back to the outside to finish and spruce the bastard up.
Finished cockpit from outside the canopy.
Gunner's station with random buttons, emergency throttle, joystick and comm setup. Hud is the big uprights with additional screens below.
Close up of the flight stick. Firing stud, two additional buttons and a toggle plus comms console.
For instances when pilot is rendered incapacitated, grip safety and push throttle. Disengages the flightstick from the guns and into the drives. Figured something like that is best placed where the gunner can't bump it.
With those parts done, going back to the outside to finish and spruce the bastard up.
I've committed the greatest sin, worse than anything done here today. I sold half my soul to the devil. -Ivan Isaac, the Half Souled Knight
Mecha Maniac
Mecha Maniac
- TheMuffinKing
- Jedi Council Member
- Posts: 2368
- Joined: 2005-07-04 03:34am
- Location: Ultima ratio regum
- Contact: