Question... Hard drives and ROM configurations...

GEC: Discuss gaming, computers and electronics and venture into the bizarre world of STGODs.

Moderator: Thanas

Post Reply
User avatar
Superman
Pink Foamin' at the Mouth
Posts: 9690
Joined: 2002-12-16 12:29am
Location: Metropolis

Question... Hard drives and ROM configurations...

Post by Superman »

I reformatted a computer, and now it freezes when I put a disk in the rom drive. I'm pretty sure it's a problem with the master/slave settings, so what is the best way to set this up? I have 2 rom drives and 2 hard drives. Which ones should be the masters and slaves? I put the jumpers on the roms to CS.
User avatar
Hawkwings
Sith Devotee
Posts: 3372
Joined: 2005-01-28 09:30pm
Location: USC, LA, CA

Post by Hawkwings »

The HD with your OS should be the master, and the other the slave. Both rom drives can be set to slave.
User avatar
Glocksman
Emperor's Hand
Posts: 7233
Joined: 2002-09-03 06:43pm
Location: Mr. Five by Five

Post by Glocksman »

Personally, I hard set the jumpers on each drive to Master or Slave instead of using CS.
But that's because I'm an old fashioned kind of guy. :lol:

Back when I ran a PATA setup, I made both hard drives the master on their respective channels and made the opticals the slaves.

However I do recall having a problem with an optical not being detected until I flashed the motherboard with a BIOS update.

If you're having problems, make sure that both your mobo and your optical drives are running the latest firmware/BIOS.
"You say that it is your custom to burn widows. Very well. We also have a custom: when men burn a woman alive, we tie a rope around their necks and we hang them. Build your funeral pyre; beside it, my carpenters will build a gallows. You may follow your custom. And then we will follow ours."- General Sir Charles Napier

Oderint dum metuant
User avatar
Superman
Pink Foamin' at the Mouth
Posts: 9690
Joined: 2002-12-16 12:29am
Location: Metropolis

Post by Superman »

Errr... So you mean like this?

Primary Master= HD with operating system
Secondary Master=other hard drive
primary slave=rom
secondary slave=rom

That?
User avatar
Uraniun235
Emperor's Hand
Posts: 13772
Joined: 2002-09-12 12:47am
Location: OREGON
Contact:

Re: Question... Hard drives and ROM configurations...

Post by Uraniun235 »

Superman wrote:I reformatted a computer, and now it freezes when I put a disk in the rom drive. I'm pretty sure it's a problem with the master/slave settings, so what is the best way to set this up? I have 2 rom drives and 2 hard drives. Which ones should be the masters and slaves? I put the jumpers on the roms to CS.
What are the jumpers on the hard drives set to?

CS stands for Cable Select, and it means that the device will automatically determine whether it is Master or Slave by its position on the cable. The middle connector is Slave; the end connector is Master.

I'm pretty sure that if, for example, you set the CD-ROM on CS and plugged the end connector into it, and set the hard drive to Master and plugged it into the middle connector, it would cause Problems, because both devices would be trying to be Master.

Generally I've found that if you're going to go CS, you should set all of your devices to CS. It's really much simpler that way.
"There is no "taboo" on using nuclear weapons." -Julhelm
Image
What is Project Zohar?
"On a serious note (well not really) I did sometimes jump in and rate nBSG episodes a '5' before the episode even aired or I saw it." - RogueIce explaining that episode ratings on SDN tv show threads are bunk
User avatar
Superman
Pink Foamin' at the Mouth
Posts: 9690
Joined: 2002-12-16 12:29am
Location: Metropolis

Re: Question... Hard drives and ROM configurations...

Post by Superman »

Uraniun235 wrote:Generally I've found that if you're going to go CS, you should set all of your devices to CS. It's really much simpler that way.
I'll set the Roms to CS, but what do I do with the drives? Do they have to be configured?
User avatar
Glocksman
Emperor's Hand
Posts: 7233
Joined: 2002-09-03 06:43pm
Location: Mr. Five by Five

Post by Glocksman »

Yes.
Most all hard drives have a diagram on the label that tells the jumper positions needed for Master/Slave/Cable Select settings.
"You say that it is your custom to burn widows. Very well. We also have a custom: when men burn a woman alive, we tie a rope around their necks and we hang them. Build your funeral pyre; beside it, my carpenters will build a gallows. You may follow your custom. And then we will follow ours."- General Sir Charles Napier

Oderint dum metuant
User avatar
Superman
Pink Foamin' at the Mouth
Posts: 9690
Joined: 2002-12-16 12:29am
Location: Metropolis

Post by Superman »

The plot thickens.

I'm thinking maybe my hard drive is messed up. I reloaded my Windows XP, but whenever I put my driver disk in, it freezes. It also won't install anything. Shit.
User avatar
Superman
Pink Foamin' at the Mouth
Posts: 9690
Joined: 2002-12-16 12:29am
Location: Metropolis

Post by Superman »

So far, I've narrowed this problem to the Roms not running. I've tried a few, and they just sort of freeze up. I've installed a few things using my USB drive.

Any ideas why the roms would do this? Is it my cable connecting them to the mother board? Could be it be a setting in bios?
User avatar
Glocksman
Emperor's Hand
Posts: 7233
Joined: 2002-09-03 06:43pm
Location: Mr. Five by Five

Post by Glocksman »

Do you have it set up the way you describe:
Primary Master= HD with operating system
Secondary Master=other hard drive
primary slave=rom
secondary slave=rom
If so, this is what I'd try.

First, go into the BIOS and make sure that the drive settings are on 'auto' for each IDE channel.
Second, while I doubt that it's a cable because your HD's are working, but you can replace the cables to eliminate that possibility.
Third, if you've set everything on CS and it's not working, reset the jumpers to hard code Master/Slave on the respective drives.

BTW, which motherboard are you using?
Sometimes there are known issues with certain hardware combos that later get resolved in BIOS/Firmware updates.
"You say that it is your custom to burn widows. Very well. We also have a custom: when men burn a woman alive, we tie a rope around their necks and we hang them. Build your funeral pyre; beside it, my carpenters will build a gallows. You may follow your custom. And then we will follow ours."- General Sir Charles Napier

Oderint dum metuant
Post Reply